UDMA 100 Support with LBA 48?
Posted: Sat Jul 03, 2004 7:00 pm
Hey everyone!
For system specs I have the following
Standard Xbox with a Homebrew Mod chip and EvoX Bios
I've installed GentooX to my F drive and the Drive is a seagate 120 gig with ATA100 support. I have also replaced the ATA cable with a ATA100 cable.
Now, my problem lies with enabling UDMA100 ...
Durring the boot process i get the following message. I could just be an idiot but could someone tell me why UDMA Mode 5 isn't working
From /var/log/kern.log
From what I am reading (please feel free to hit me if im wrong) UDMA33 is only working. Is this because my CDRom is capped at that or?
Which is wierd because, when I start GentooX from the EvoX pannel it says that the Drive is UDMA5 with LBA 48 supported
Any thoughts and advice is greatly appreciated
Cheers!!
For system specs I have the following
Standard Xbox with a Homebrew Mod chip and EvoX Bios
I've installed GentooX to my F drive and the Drive is a seagate 120 gig with ATA100 support. I have also replaced the ATA cable with a ATA100 cable.
Now, my problem lies with enabling UDMA100 ...
Durring the boot process i get the following message. I could just be an idiot but could someone tell me why UDMA Mode 5 isn't working
From /var/log/kern.log
Jul 3 18:50:03 xbox kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jul 3 18:50:03 xbox kernel: NFORCE: IDE controller at PCI slot 00:09.0
Jul 3 18:50:03 xbox kernel: NFORCE: chipset revision 177
Jul 3 18:50:03 xbox kernel: NFORCE: not 100%% native mode: will probe irqs later
Jul 3 18:50:03 xbox kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Jul 3 18:50:03 xbox kernel: AMD_IDE: nVidia Corporation nForce IDE (rev b1) UDMA100 controller on pci00:09.0
Jul 3 18:50:03 xbox kernel: ide0: BM-DMA at 0xff60-0xff67, BIOS settings: hda:DMA, hdb:DMA
Jul 3 18:50:03 xbox kernel: hda: C/H/S=0/0/0 from BIOS ignored
Jul 3 18:50:03 xbox kernel: hdb: C/H/S=0/0/0 from BIOS ignored
Jul 3 18:50:03 xbox kernel: hda: ST3120026A, ATA DISK drive
Jul 3 18:50:03 xbox kernel: hdb: SAMSUNG DVD-ROM SDG-605B, ATAPI CD/DVD-ROM drive
Jul 3 18:50:03 xbox kernel: blk: queue c0385c00, I/O limit 4095Mb (mask 0xffffffff)
Jul 3 18:50:03 xbox kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Jul 3 18:50:03 xbox kernel: hda: attached ide-disk driver.
Jul 3 18:50:03 xbox kernel: hda: host protected area => 1
Jul 3 18:50:03 xbox kernel: hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=14593/255/63, UDMA(33)
Jul 3 18:50:03 xbox kernel: hdb: attached ide-cdrom driver.
Jul 3 18:50:03 xbox kernel: hdb: ATAPI 16X DVD-ROM drive, 512kB Cache, UDMA(33)
Jul 3 18:50:03 xbox kernel: Uniform CD-ROM driver Revision: 3.12
Jul 3 18:50:03 xbox kernel: Partition check:
From what I am reading (please feel free to hit me if im wrong) UDMA33 is only working. Is this because my CDRom is capped at that or?
Which is wierd because, when I start GentooX from the EvoX pannel it says that the Drive is UDMA5 with LBA 48 supported
Any thoughts and advice is greatly appreciated
Cheers!!