what ppl?
btw what can you do with a 733mhz, 64mb memory, no 3D.... anyway,??..run a server.
a desktop pc? um..good luck!!
i want to run a server with no GUI.. 'X'. after apache2 gets installed i'll use runlevel 3 to start stop the server.
Dreaded question: When is 3.1 coming out?
-
- Gentoox Guru!
- Posts: 553
- Joined: Tue Oct 07, 2003 9:57 pm
- Location: MOUNT TAPE U1439 ON B3, NO RING
Try running Openbox, instead of XFCE4. It will go faster._mikec_ wrote:what ppl?
btw what can you do with a 733mhz, 64mb memory, no 3D.... anyway,??..run a server.
a desktop pc? um..good luck!!
i want to run a server with no GUI.. 'X'. after apache2 gets installed i'll use runlevel 3 to start stop the server.
MOUNT TAPE U1439 ON B3, NO RING
Q: HOW DO I RUN MAGIC ??
A: You run magic by not typing in capital letters.
Q: HOW DO I RUN MAGIC ??
A: You run magic by not typing in capital letters.
emerge -av obconf:
configure.ac:3: version mismatch. This is Automake 1.7.5,
configure.ac:3: but the definition used by this AM_INIT_AUTOMAKE
configure.ac:3: comes from Automake 1.7.9. You should recreate
configure.ac:3: aclocal.m4 with aclocal and run automake again.
make: *** [Makefile.in] Error 1
!!! ERROR: x11-wm/openbox-3.2-r1 failed.
!!! Function src_compile, Line 36, Exitcode 2
!!! (no error message)
gentoox is a pain.
configure.ac:3: version mismatch. This is Automake 1.7.5,
configure.ac:3: but the definition used by this AM_INIT_AUTOMAKE
configure.ac:3: comes from Automake 1.7.9. You should recreate
configure.ac:3: aclocal.m4 with aclocal and run automake again.
make: *** [Makefile.in] Error 1
!!! ERROR: x11-wm/openbox-3.2-r1 failed.
!!! Function src_compile, Line 36, Exitcode 2
!!! (no error message)
gentoox is a pain.
Linux, not good for newbies with no skills at all, u better be viewing the network from a Window to the world and using micro soft wares.
-
- Gentoox Guru!
- Posts: 553
- Joined: Tue Oct 07, 2003 9:57 pm
- Location: MOUNT TAPE U1439 ON B3, NO RING
Follow one of these paths:_mikec_ wrote:emerge -av obconf:
configure.ac:3: version mismatch. This is Automake 1.7.5,
configure.ac:3: but the definition used by this AM_INIT_AUTOMAKE
configure.ac:3: comes from Automake 1.7.9. You should recreate
configure.ac:3: aclocal.m4 with aclocal and run automake again.
make: *** [Makefile.in] Error 1
!!! ERROR: x11-wm/openbox-3.2-r1 failed.
!!! Function src_compile, Line 36, Exitcode 2
!!! (no error message)
gentoox is a pain.
- Do what it tells you.
- Emerge Fluxbox or Blackbox, instead.
- Emerge FVWM, instead.
- Etc.
MOUNT TAPE U1439 ON B3, NO RING
Q: HOW DO I RUN MAGIC ??
A: You run magic by not typing in capital letters.
Q: HOW DO I RUN MAGIC ??
A: You run magic by not typing in capital letters.