No USB devices (xpad/xir) in MCE

Ask questions about Gentoox MCE here!
Post Reply
Radak
Newbie
Posts: 2
Joined: Tue Aug 24, 2004 1:06 am

No USB devices (xpad/xir) in MCE

Post by Radak » Tue Aug 24, 2004 1:14 am

I've installed MCE on my xbox and I am unfortunately unable to control it, because I have neither xpad nor xir working once it boots. (This same problem was described by someone else in passing in another thread.)

It seems my problem is one of lack of USB devices working:

Code: Select all

# cat /proc/bus/usb/devices
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB OHCI Root Hub
S:  SerialNumber=c5ece000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
And that's it. It claims to see a hub (and only one, where there should be two) and nothing else.

If I boot the Gentoox Stardust CD, xpad works fine, and I find something very different in usbdevfs:

Code: Select all

> cat /proc/bus/usb/devices
T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB OHCI Root Hub
S:  SerialNumber=c4c35000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 4
B:  Alloc= 63/900 us ( 7%), #Int=  3, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB OHCI Root Hub
S:  SerialNumber=c4c33000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=58(unk. ) Sub=42 Prot=00 Driver=usb-xboxir
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=16ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=59(unk. ) Sub=00 Prot=00 Driver=(none)
T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=12  MxCh= 3
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=045e ProdID=001c Rev= 5.00
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 64mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   1 Ivl=255ms
T:  Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=045e ProdID=0285 Rev= 1.00
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=58(unk. ) Sub=42 Prot=00 Driver=xpad
E:  Ad=82(I) Atr=03(Int.) MxPS=  32 Ivl=4ms
E:  Ad=02(O) Atr=03(Int.) MxPS=  32 Ivl=4ms
All devices are properly seen, including both hubs.

Both kernels have all the appropriate USB modules loaded (usbcore, usb-ohci, input, hid, keybdev, usbkbd, usbmouse, mousedev, xpad, joydev).

Any ideas?

Radak
Newbie
Posts: 2
Joined: Tue Aug 24, 2004 1:06 am

Post by Radak » Tue Aug 24, 2004 2:12 am

Okay, I figured it out. I was neglecting to pass the kernel kbd-reset on the command line and that was apparently breaking USB.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest